MC Primer CSG
To be used with Flortex MC or Cretex MC (inc. Deepfill version), for use between -40°C to 0°C.
Frequently bought together
MC Primer CSG Product Details
For use with Flortex MC or Cretex MC (inc. deepfill version) – for use between -40°C to 0°C.
MC Primer Standard is used at a temperature of +1°C or higher.
MC Primer CSG is used at a temperature of –1°C or lower.
Pot life:Standard: 15-20 mins @ 10°C
CSG: 15-20 mins @ -10°C
Application temperature:Standard: -40°C – 0°C
CSG: -30°C – 0°C
Initial cure time:1-1.5 hours
Full strength cure time:2 hours
Full compressive strength:75N/mm2
Full tensile strength:7.6N/mm2
Full flexural strength:24N/mm2
Number of parts supplied:2
Coverage:15-20 sq.m. per 5kgs unit
Please consult the technical data sheet for full technical product data.
Thorough substrate preparation is essential.
Powerfloated concrete – use a Vacuum Assisted Shotblaster to remove weak laitence and provide a surface key for the coating. If this is not possible, chemically etch with Polycote Etch IT then rinse thoroughly and allow to dry.
Loose paint – remove, using a Vacuum Assisted Shotblaster, Floor Grinder or equivalent method.
Loose or friable concrete – use a Vacuum Assisted Shotblaster. If this is not possible, chemically clean with Polycote Etch IT then rinse thoroughly and allow to dry.
Oil or grease – use Hot Compressed Air for large areas of contamination. Smaller, isolated deposits may be chemically cleaned with Polycote Degrease IT, then rinsed thoroughly and allowed to dry.
See relevant Data Sheet prior to application.
Once prepared, the area must be kept clean and free of traffic.
Caution – MC Primer is methyl methacrylate based and has a characteristic odour during the vaporising of the solvent. Although non-toxic and non-injurious to health, this can cause tainting and OPEN food products should therefore be removed or sealed during and following application until the vapour has dispersed.
Before mixing this product you must be totally prepared; for rapid uninterrupted application of the complete mixed quantity within 10 minutes. Having fully prepared the substrate, add part ‘B’ to part ‘A’ and thoroughly mix for at least 3 minutes. For best results use a heavy duty slow speed drill with a mixing paddle.
Ensure thorough mixing as an unmixed product will result in a poor or non-cure situation.
Apply by brush, roller or squeegee, making sure that the surface is completely covered. Particular attention should be given to doorways and other areas of high traffic. When finished, do NOT scrape the remaining contents from the container as this will invariably include unmixed raw resin.
When priming for Flortex MC – it is advisable to scatter kiln dried quartz aggregate (0.3 – 0.6mm) into the wet MC Primer coating at a rate if 1kg/m2 to increase adhesion of the repair material.
Jointex CSG (Cold Store Grade)
Joint sealant for cold stores, freezers and fridges. Cures down to -30°C. Very fast curing in only 1-2 hours depending upon...£167.35 ex. VAT
£200.82 inc. VAT Add to basket
Cretex MC Deepfill CSG (Cold Store Grade)
Cretex® MC Deepfill CSG is an extremely fast-curing cold store grade concrete floor repair. It is designed for larger or deeper...£196.74 ex. VAT
£236.09 inc. VAT Add to basket
Cretex MC CSG (Cold Store Grade)
Cretex® MC CSG is an extremely fast-curing concrete floor repair mortar down to -40oC. It has an incredible 75N/mm² compressive strength...£168.80 ex. VAT
£202.56 inc. VAT Add to basket
Flortex MC CSG
A methacrylate based high build resin floor coating – fast curing even at –40°C. Initial cure 1-1½ hours – minimal...£218.90 ex. VAT
£262.68 inc. VAT Select options