WD Primer is a high adhesion water-dispersed epoxy primer offering a high bond strength to all substrates.
- Our most popular primer
- An ideal primer for floors and metal coatings
- Works on old and new concrete
- Compatible with polymer modified cementitious screeds
- High adhesion to many substrates
- Solvent free
- Protective water dispersed floor coating
- Resistant to oils and chemicals
Frequently bought together
WD Primer Product Details
WD Primer is a professionally formulated epoxy floor coat to penetrate and cure within the surface, filling the texture and hardening the substrate prior to the application of a top coat. This Water Dispersed primer is a unique formulation which includes includes at least twice the resin content of the standard primers available, and incorporates advanced adhesion promoters, adhering strongly to the flooring, metal or other surface and creating a high strength chemical bond when over-coated, for a long lasting finish.
Use on: Old and new concrete and polymer modified cementitious screeds
Use where: Internal/External
Typical industries: Commercial and industrial premises, such as dairies, hospitals, food and industrial areas
Type of job: Preparation of a surface prior to over-coating. to ensure a good inter-coat bond, the topcoat should be applied between 24 and 48 hours after application of the Primer
Approximate coverage: 5kg – 25m-30m2
Special features:Extra chemical resistance, oil resistant, promoted adhesion for a long lasting finish, solvent free
Pot life:Approximately 60 minutes @ 20oC
Application temperature:10oC to 25oC
Cure time:Approximately 24 hours
Number of parts supplied:2
Primer for:Polycote Flortex range of epoxy products
Please consult the technical data sheet for full technical product data.
Preparation:Thorough substrate preparation is essential.Recommended methods are:Powerfloated concrete – use a Vacuum Assisted Shotblaster to remove weak laitence and provide a surface key for the coating. If this is not possible, chemically etch with Polycote Etch IT then rinse thoroughly and allow to dry.Loose paint or rust – remove, using a Vacuum Assisted Shotblaster, Floor Grinder or equivalent method.
Loose or friable concrete – use a Vacuum Assisted Shotblaster. If this is not possible, chemically clean with Polycote Etch IT then rinse thoroughly and allow to dry.Oil or grease – use Hot Compressed Air for large areas of contamination. Smaller, isolated deposits may be chemically cleaned with Polycote Degrease IT, then rinsed thoroughly and allowed to dry.Terrazzo, quarry or ceramic tiles – treat with Polycote Etch IT, rinsing thoroughly after 20 minutes.
See relevant Data Sheet prior to application.Once prepared, the area must be kept clean and free of traffic.
Mixing:Having fully prepared the substrate, stir the individual components before mixing together. Add Part ‘B’ to Part ‘A’ and thoroughly mix for at least 3 minutes. For best results use a heavy duty slow speed drill with a mixing paddle.Ensure thorough mixing as an unmixed product will result in a poor or non-cure situation.
Application:Prior to application of epoxy coatings – apply WD Primer by brush, roller or squeegee, making sure that the surface is completely covered. Particular attention should be given to doorways and other areas of high traffic. When finished, DO NOT scrape the remaining contents from the container as this will invariably include unmixed raw resin.IMPORTANT – Ensure thorough coverage of porous surfaces, working the primer well into the surface. Failure to do this may allow the floor to ‘breathe’ and result in pinholing or bubbles in the epoxy top coat.Prior to application of cementitious screeds – apply as above, then sprinkle kiln-dried quartz (ideally 0.3-0.6mm) onto the WET primer to provide a mechanical key and allow to cure. Any loose quartz should then be brushed off before laying the screed.
Flortex EP is a very heavy duty, solvent free epoxy floor coating with a 100% solids content. Capable of withstanding...£128.90 ex. VAT
£154.68 inc. VAT Select options
Incredibly strong epoxy concrete floor repair (70N/mm2). Withstands virtually any traffic (even to a feather-edge) AND an easy 1:1 mix...£96.80 ex. VAT
£116.16 inc. VAT Select options
This product is currently unavailable but please see the suggested alternative Jointex PU Our flagship expansion joint sealant. Extremely tough (protecting...£154.80 ex. VAT
£185.76 inc. VAT Select options
Flortex Professional Epoxy Floor Paint
Exceptionally hard wearing, high build 100% solids epoxy floor coating. The best available! Slip Resistant, Extra Fast Hardening versions also available. ...£128.90 – £218.90 ex. VAT
£154.68 inc. VAT Select options