| Quantity | Discount (%) | Price |
|---|---|---|
| 1 - 4 | — | £167.35 |
| 5 - 9 | 2.75 % | £162.75 |
| 10 - 19 | 5.67 % | £157.86 |
| 20 - 49 | 8.87 % | £152.50 |
| 50+ | 11.08 % | £148.80 |
Price Match Guarantee
Next day delivery*
30 Day trade accounts
Joint sealant for cold stores, freezers and fridges. Cures down to -30°C.
Very fast curing in only 2 hours depending upon temperature.
Jointex™ CSG is a two part acrylic based flexible jointing compound combining a viscous resin and fine graded fillers.
It is specially formulated to achieve a rapid cure at very low temperatures. It offers high strength with excellent elongation characteristics, allowing up to 100% movement within the joint.
Jointex™ CSG is ideal for rapid repairs to concrete expansion or construction joints in cold stores and other industrial areas of very low temperature.
Suitable substrates: Jointex™ CSG may be applied to old and new concrete.
Colour: Jointex™ CSG is grey as standard. Other colours are available to order subject to minimum quantity.
Packaging: Jointex™ CSG is supplied in pre-measured quantities as a two part 6.0kg unit, comprising of a resin Part ‘A’ and hardener/filler Part ‘B’.
Pot life: 10- 15 mins @ 20°C
Application temperature: 0°C to – 30°C
Depth of repair (1 layer): 10mm – 25mm
Fully cured strength: 26N/mm2
Number of parts supplied: 2
Priming required: No. Only for very porous surfaces – use Polycote Primer CSG
Please consult the technical data sheet for full technical product data.
Surface Preparation
THOROUGH SUBSTRATE PREPARATION IS ESSENTIAL.
All joints must be clean, dry and free of dust, loose material or previous joint sealant. Shotblasting is recommended. A gas torch may be used to help remove oil or moisture from the surface.
If the edges have broken away – repair using Polycote Cretex™ MC. Depending on the extent of the repair, the Cretex™ material may be supported using a thin polythene covered batten until firm, OR the joint may be totally filled with Cretex and re-opened once cured using a suitable width of diamond saw cut, providing a clean edged joint. Please contact Polycote Technical Helpline for advice and the appropriate Data Sheets.
Jointex™ CSG does not normally require a primer, unless the substrate is very porous, in which case Polycote MC Primer CSG should be used.
The prepared joint should be part filled using flexel or kiln dried sand, leaving a minimum depth of 10mm.
Tape may be applied to mask the surface each side of the joint during pouring, but this should be removed as soon as material is placed.
Caution – Jointex™ CSG is methyl methacrylate based and has a characteristic odour during the vaporising of the solvent. Although non-toxic and non-injurious to health, this can cause tainting and OPEN food products should therefore be removed or sealed during and following application until the vapour has dispersed.
Mixing
COOL THE MATERIALS IN A FREEZER PRIOR TO MIXING.
Empty the resin Part ‘A’ into a clean plastic mixing container and add the complete quantity of hardener/filler Part ‘B’. Mix thoroughly to ensure complete dispersion of the hardener. For best results use a heavy duty slow speed drill with a mixing paddle.
ENSURE THOROUGH MIXING AS AN UNMIXED PRODUCT WILL RESULT IN A POOR OR NON-CURE SITUATION.
Application
Apply immediately using a jug or suitable container to pour the mix directly into the joint.
For a professional finish and maximum joint protection, fill to slightly above the level of the surrounding area, but not to the point of overflow. Once cured, the top of the filler may be chiselled flush to the level of the floor.
Application Temperature
Normal application temperature is between 0˚C and -30˚C.
We promise to beat any quote in the UK when quoting like for like.
