Highly flexible, self-levelling floor screed
A free-flowing, fibre-reinforced, self-levelling cement floor screed. Fast drying times to enable a rapid return to use.
| Quantity | Discount (%) | Price |
|---|---|---|
| 1 - 4 | — | £42.80 |
| 5 - 9 | 5.61 % | £40.40 |
| 10 - 19 | 10.98 % | £38.10 |
| 20 - 49 | 14.49 % | £36.60 |
| 50 - 99 | 18.57 % | £34.85 |
| 100+ | 23.83 % | £32.60 |
Price Match Guarantee
Next day delivery*
30 Day trade accounts
Easi-Screed Flexible is a free-flowing, fibre reinforced, cementitious self leveller. It cures fast to enable a rapid return to use.
Designed for heavy domestic or light industrial use it is suitable for all common substrates and is ideal for use over underfloor heating.
Easi-Screed Flexible can be used on the following: Timber boards, plywood, chipboard, underfloor heating, concrete, sound asphalt, ceramic, quarry and natural stones.
Easi-Screed Flexible is grey in colour.
Easi-Screed Flexible is supplied in 25kg bags.
The pot life of Easi-Screed Flexible once mixed is approximately 20-30 minutes at 20°C.
Initial curing takes place within 2-3 hours depending on temperature.
Surfaces should be suitable to accept floor coverings after 12-24 hours.
Important note: Should Easi-Screed Flexible be installed over underfloor heating, please ensure the screed is left for a period of 14 days to fully cure before the underfloor heating is turned on. Finally, please also ensure the temperature of the heating is increased in increments of no more than 2°C per day.
Normal application temperature is between 10˚C and 35˚C.
The coverage per 25kg unit of Easi-Screed Standard mixed with 4.5L of water is as follows:-
2.3m² at 6mm depth
1.35m² at 10mm depth.
The shelf life is up to 6 months subject to storage in dry conditions. Store off ground, unopened in frost-free conditions at a temperature between 10˚C and 30˚C.
Thorough substrate preparation is essential.
The surface should be clean, sound and free from all loose particles such as old adhesive residues, dust, plaster spillages, grease, paint, polish and any other compound, which may become softened by the introduction of water or be detrimental to the required bond.
Concrete bases and screeds must be fully cured and firm. Surface hardeners and curing membranes must be removed prior to screeding.
Sub-floors must conform to the dryness requirements of BS8203 1987 and must incorporate an effective damp proof membrane. Relative humidity should be less than 75%.
The screed may be applied onto a suitable surface damp proof membrane where a good mechanical key has been provided.
Underfloor heating must be switched off at least 7 days before application of the screed and left off for at least 14 days. The temperature should then be increased in increments of no more than 2°C per day.
Application on newly laid underfloor heating will require the use of our Easi-Screed Primer, if applying directly to a foil backed insulation, such as Celotex.
Mixing is achieved by mixing the powder to 4.5 litres of clean water.
Gradually add the entire 25kg quantity of powder whilst mixing with a heavy duty slow speed drill and mixing paddle. Mixing by hand does not readily give a thoroughly or evenly mixed product.
Mix for at least 2 minutes to allow the additives to dissolve and produce a homogenous mix which should be lump free and a consistency of single cream. When mixed allow to stand for 1 minute after which the screed is ready for application.
Do not mix more than can be applied in 25 minutes. Do not add excess water.
By trowel or pump. Trowel: Pour a small quantity onto the prepared surface and trowel down lightly. Pump application: Prior to laying the mixed compound carry out a flow test using a flow ring (30mm diameter x 50mm long). A flow diameter of 110-130mm should be achieved, adjust mix accordingly to comply to this flow criteria. Periodically check to ensure mix remains in limit. We advise the use of a spiked roller to ensure a close tolerance surface is achieved. Cementitious screeds are susceptible to damage from liquid and chemical attack (including prolonged or constant use of water) and should therefore be sealed suitably prior to the use of such products.
Our flexible self-levelling screed is one of our latest formulations and is superior compared to traditional screeds. It has been designed using the highest quality raw materials for concrete floors that are subject to movement, vibration or where underfloor heating is used making this one of the best hard-wearing floor screeds.
An extremely easy-to-apply screed, after simply mixing with water, and can be laid as a thin layer from as little as 2mm thick, or up to a thickness of 50mm.
The fibre-reinforced, protein-free design is highly flexible, yet cures to 34N/mm² making it an incredibly strong levelling cement screed with a superb bonding agent.
Being protein free the floor screed can be used in biologically sensitive areas, ideal for use in hospitals, laboratories, food preparation areas, food shops, restaurants, schools, care homes etc.
Self-Levelling Screed
This self-levelling screed is suitable to prepare and level uneven internal subfloors. It is suitable to receive various floor coverings such as vinyl, carpet and linoleum.
Flexible & Adaptable
Dues to its flexible nature it is ideal for many different types of flooring, including floors with underfloor heating or floors made from timber boards, ply, and chipboard.
Use On Various Substrates
It can also be poured over concrete floors, sound asphalt, ceramic floor tiles, bitumen, anhydrite/ gypsum screeds, vinyl, quarry, and natural stone.
For Best Results
Concrete and sand cement screeds must be dry, and any laitance or surface treatments removed before the floor screeding process is started.
It is grey in colour and supplied in 20kg units.
Floor screeds are extremely easy to apply, after simply adding water, and you can lay it from as little as 2mm thick, or up to as much as 50mm thick.
Should it be applied in an industrial application, we strongly advise it is finished with an epoxy coating such as Flortex SG or Flortex Professional to provide an impervious, hard wearing surface.
Polycote have a wide range of different types of products that may be suitable for your project.
A 20kg unit will cover a floor area of approximately 3.7m² at a thickness of 3mm.
Please do not hesitate to contact us for flooring advice regarding your project. Whether it’s big or small our friendly team will advise the use of this product or its suitability for your particular application. They will suggest other considerations that might get the job done and provide you with a final cost for the whole flooring process.
Our aim is to provide all the technical help you need to make an informed choice and achieve total success. Whether its advice about a high strength concrete topping, a concrete floor or structural performance, our experts can provide the essential help and support you need to ensure your project is a success from the start of the process to the end.
We will point out what flooring you need to achieve a positive diy experience or arrange the right approved installer to lay the flooring.
We promise to beat any quote in the UK when quoting like for like.
