Cretex OT Mortar XFH
Floor repair mortar for oil contaminated surfaces including both concrete and wood. Incredibly strong floor repair and resistant to heavy use / traffic
- High oil tolerance floor repair mortar
- Solvent free, non-toxic and non-taint
- Extremely easy to use
- Suitable for use in food environments
- Excellent performance on damp walls and floors
- Standard version available
- 33kg unit
£297.88 (ex VAT)
Cretex OT Mortar XFH Product Details
Cretex OT Mortar has been specifically formulated to answer the need for repairs in both oily or greasy conditions.
It not only has the unique ability to adhere strongly to oil contaminated floors but is also excellent for use where rising damp is an issue.
Solvent free, non-toxic and non-taint
Extremely easy to use
Suitable for use in food environments
XFH version available where downtime is limited
From a unit size of 32kg the approximate coverage is 3 sq.m. @ 5mm thickness.
Pot life:30 mins @ 20oC
Application temperature:5oC – 30oC
Initial curing time:6-8 hours
Walk-on time:18-24 hours
Overcoat time:within 36 hours
Full cure:2-3 days
Depth of repair (1 layer):Feather edge – 200mm
Fully cured compressive strength:68N/mm2
Fully cured flexural strength:80N/mm2
Fully cured tensile strength:45N/mm2
Number of parts supplied:3
Priming required:For very porous/unstable surfaces, apply coat of mixed resin before adding quartz sand
Please consult the technical data sheet for full technical product data.
Thorough substrate preparation is essential.
Remove all loose material. Wire brushing is advisable. Sweep clean or vacuum.
The surface must be free from grease, oil or contamination. Polycote Degrease IT may be used to clean the area but this must be thoroughly rinsed off and the substrate dried, before applying Cretex OT Mortar. Alternatively, should the surface be particularly porous or weak, Polycote OT Primer has superb penetrative properties and will seal and ‘lock’ the substrate. The primer should be allowed to fully cure before the application of the OT Mortar. See relevant data sheets for full information.
Having fully prepared the substrate, add the whole of Part B to the whole of Part A and mix thoroughly for at least 3 minutes. For best results use a slow speed drill with a mixing paddle. Finally, pour the liquid into the large bucket and add the aggregate to the desired consistency. Ensure thorough mixing as an unmixed product will result in a poor or non-cure situation.
Apply by trowel, or by hand for small isolated areas, wearing suitable protective gloves.
Being resin-rich, Cretex OT Mortar has a typically sticky consistency and smoothing may be assisted by wetting the trowel using Polycote Solvent Cleaner as a release agent.
If when trowelling the mortar the texture remains ‘open’ this can be easily ‘closed’ by slightly tamping the surface with the trowel. This can provide an extremely hard wearing and completely sealed surface.
For vertical repairs – where step nosings or expansion joint edges have broken away, the vertical face of the repair material should be supported to prevent slumping.
Suitable sized wooden shuttering should be covered with polythene to reduce adhesion, and should be removed as soon as the material is firm.
Only logged in customers who have purchased this product may leave a review.
You may also like…
Cretex OT Mortar Standard
Ultra tough repair mortar for oil contaminated floors. Solvent free, non-toxic & non-taint£255.27 (ex VAT)
Fast curing twin pack epoxy expansion joint filler. Cures in 1 hr. High flexural strength£158.75 (ex VAT)
Exceptionally hard wearing, high build 100% solids epoxy floor coating. The best available!From Only: £128.90 (ex VAT)
EP Primer XFH
Ultra low viscosity ensuring maximum penetration. Extra fast hardening. 100% solids epoxy£109.80 (ex VAT)
There are no reviews yet.